Home > Jerry Brown Fishing Line > Spectra Line Needles & Tools >
Daho Hollow Threading Set of 3 Needles
Daho Hollow Threading Set of 3 Needles
Item #: HTN-Custom
Availability: In Stock
Usually ships In 1 to 4 Days
Needle Choice #1: Needle Choice #2: Needle Choice #3:
Set of 3 DaHo Hollow Threading Rigging Needles Free Shipping
Your choice of 3 Threading Needles, free shipping anywhere in the USA.
Your choice of 3 DaHo Mono Hollow Threading Needles for rigging top shots and spectra looped wind on leaders using hollow core spectra braided fishing lines. See our needle sizing buyer's guide and tech tips section for additional information on selecting and using DaHo Monofilament Hollow Threading Needles.
The picture below depicts the
various terminating ends of the DaHo Rigging Needle Products. The hollow threading needles are hollow throughout to allow the threading of the fishing line. The product pictured on the left is the point found on all Daho needle products. The reverse latch mechanism is pictured in the center, and on the right is the loop of the
Loop Splicing needle product.
DaHo Hollow Threading Needles Size Chart
Daho recommends that you select a needle that is at least .002" larger than the line your intend to use.
||10 to 20# Small Threading Needle
||up to 60#
||20 to 30# Small Threading Needle
||up to 80#
||30 to 40# Small Threading Needles
||up to 80#
||40 to 50# Threading Needle
||60 to 130#
||50 to 60# Threading Needle
||80 to 130#
||60 to 80# Threading Needle
||100 to 300#
||80 to 100# Threading Needle
||100 to 300#
||100 to 130# Threading Needle
||130 to 300#
||130 to 150# Threading Needle
||200# and up
||150 to 200# Threading Needle
||200# and up
||200 to 300# Big Threading Needle
||300# and up
||300 to 400# Big Threading Needle
||400# and up
||400 to 500# Big Threading Needle
||500# and up
This will facilitate the use of the needle and allow for an easier rigging process.
Table of Monofilament & Fluorocarbon Fishing Line Diameters by Manufacturer
DaHo Hollow Core Spectra & Top Shot Rigging Needles
Hollow Threading Needles:
The new DaHo Threading Needles have been sized by their length so if a customer has more than one of them, they can stand them on their open end and find the one they want by its length, compared to all the other threading needles. The smallest threading needle, the 50# size, has a length of 5.6". Subsequent sized needles are .1" longer than the last, the largest 200# size being 6.2" in length.
The DaHo Hollow Spectra Threading Needles are hollow inside, except for the point, so additional material, typically monofilament or fluorocarbon line, can be inserted into the needle. Then, the needle together with the internal mono line, is inserted, or threaded, into the hollow center section of the spectra braid. The needle, and attached mono line, is then inserted inside of the spectra a distance of 3 to 5 feet to provide maximum strength of the join. Due to the thick surface of monofilament fishing lines, the end point of the spectra must be finished to secure it. The finishing process is done by employing any of these methods:
* Gluing using Line One Adhesive from Jerry Brown Industries
* Combination of the above
The use of any of the methods outlined above ensures the join will not slip before the compression pressure occurs to in the hollow spectra line to hold the joined lines together.
The primary size of the threading needle is the ID, or Internal Diameter, indicating the approximate size of monofilament line that it will hold inside. The needle size you need is determined by the size of the monofilament line you are using. Typically, these sizes can be found on the spool the line was purchased on, or by visiting the line manufacturer’s website. You will usually want to get a needle that will fit the line you are using, and provide and additional .002" of 'free' space to ease the insertion of your line. If the monofilament line is too large for the needle, you will have to cut it down, which is difficult and time intensive. The needles will easily hold smaller sizes of monofilament lines. DaHo Products offers most typically used sizes in their standard product offerings. Even though they are named for the typical size of mono that they will hold, you should select your needles by the actual size of your monofilament nylon fishing line.
The construction process of the DaHo Hollow Threading needles uses thinner walled tubing to manufacture the needles. This is to assure the overall size of the needle will remain as small as possible, while offering the largest interior size to hold the monofilament nylon fishing line. Thinner is definitely better.
General Usage Helpful Hints
These are helpful hints that can assist you in doing many of the basic tasks that are required in using hollow spectra needle tools. They are discussed here, in detail, so that all of the procedures that use these basic tasks can just reference them in their instructions.
Starting a needle in the end of your hollow spectra line - One of the more 'challenging' tasks, at first, can be to initially insert the point of your needle into the middle, hollow section of your spectra line. The spectra line is usually fuzzy at the end and will flatten out when any pressure is put on it, making the center hollow chamber of the braid difficult to find.
The recommended place to work with your needles is on the edge of a table or other flat surface. Put the line on the top of the table, straight for a foot or so, and place the end of the line at the edge of the table. This position gives you the ability to position the needle in the right position so it appears that it is extending from the line's position.
You need to use the point of your needle, the smaller the better for this purpose at first, to find the center of the spectra line. Once you have found the hollow center of the braid, the outer part of the line should look consistent in color and texture, and your needle should go up inside the spectra line easily, depending upon the outer size of the needle and the size/weight of the line.
If your needle point keeps going through the line or you can see the needle being exposed through the line material in a non-consistent manner, your needle is not in the hollow center section of the line. Try and repoint the needle toward the center of the spectra line when trying to insert it, will help find the open braid center.
Trying to make the end of the spectra line more round can also help. Sometimes a little twirling action on the needle will also help it find the center of the braid. If you think the end of the spectra line has been abused too much, cut off an inch or so and reposition the line at the edge of the table and try again.
It really very simple to do once you have the hang of it.
Inserting a needle into the side of the line - Many procedures require you to insert your needle into the side of your hollow spectra line. In this task, you also are looking for the hollow center of the braid as when you are starting at the line's end. But in this task, you must start the insertion of the needle point at a 45% angle to the spectra line.
Once the needle point has entered the spectra line and before the point hits the table surface, start bringing the angle of the needle down towards the line while searching for the line's hollow center. A good way of doing this is to hold the line down on a table surface about 1/4" down the line, and using the inserted point of the needle, lift up the line a little while it is bunching up, searching for the center.
As with the end entry method, once you have found the hollow center channel, your needle will start going up the line and it will also be a consistent size and texture.
Feeding the needle inside the hollow center of the spectra line - Regardless of how you started your needle into the hollow center braid of the spectra line, feeding the needle and its attached contents, if any, is done the same way. You always want the line stretched out straight, at least a foot or more if possible, on a table or other surface. Sit with the needle in hand, pointed at the place the line comes off of the surface about 6 inches away.
Thread the line onto the needle, keeping the needle in the same straight line as the spectra line being pulled off of the table surface. The shape of the needle point will keep the needle in the spectra line's hollow middle as long as the needle and line are kept in a straight line.
Pull the line over the needle, from the point down a few inches on the needle. You will develop a process with your hands to pull the line onto the needle with one set of fingers, and hold it on the needle with the other hand until it bunches up on the back part of the needle.
When this happens, hold the needle close to the point, and reaching toward the back of the needle, slide the bunched up line off the needle and down any attached lines, being sure not to put pressure on any attached lines that could release them from the needle.
You can continue in this manner until you have gone as far as needed to complete the task. When you are at that point, you just reach up and hold the line at the needle point, fold it over and push the needle point out of the spectra line. After the needle is removed, usually along with any attached line ends, the spectra line being threaded, will have no ill effects from the process.
Hollow spectra line and needle sizes - The middle of each size/weight of hollow spectra line is only so big. We have attached our recommendations of applicable spectra line sizes for each of our needle products on Product Offerings page. If your needle is very difficult to thread inside of your hollow spectra line, you may want to recheck our line sizes.
Our needle should go up the specified size/weight of the spectra lines we specified with our products. But, all brands of hollow spectra line products are not exactly the same size. Also, each person using our needles, may have different perceptions of what does, and does not, work right.
If your needle feels tight while threading it in the spectra, you might try to use your fingernails, in a light manner, to move the line down the shaft of the needle. If you still think our needle is too large for your spectra line, you might try to first run an appropriately sized loop splicing needle up the line to 'open up' the line. This opens up the braid structure a little, so that a larger needle can comfortably fit into the line.
PayPal Express Checkout